What you’ll explore
Which hole squirts the farthest? In this lab you poke holes at three heights in a tall water tank and test your intuition against a real physics simulation.
Challenge levels
- Ten meters down. A diver swims 10 m below the surface of a freshwater lake. What is the total pressure on them, in atmospheres (atm)? (ρ = 1000 kg/m³, g = 9.81 m/s², 1 atm = 101 325 Pa)
- Which jet wins?. A 2 m deep tank has holes at 0.5 m, 1.0 m and 1.5 m above the floor. The lowest hole has the most pressure. Which hole’s jet lands farthest from the tank? Type its height in meters.
- Hit the bucket. One hole, 2 m of water. Choose the hole height so the jet lands in the bucket 1.60 m from the wall (±3 cm).
- What if: the tank is on Mars. Same 2 m tank and three holes, but on Mars (g = 3.71 m/s²). How far from the wall does the MIDDLE jet land, in meters?
- The deepest place on Earth. The Challenger Deep in the Mariana Trench is 10 994 m below the sea surface. What is the pressure at the bottom, in atm? (seawater ρ = 1025 kg/m³)
Key ideas
Show the explanations (spoilers: try the levels first)
- P = P₀ + ρgh = 101 325 Pa + 1000 × 9.81 × 10 Pa ≈ 199 400 Pa ≈ 1.97 atm. Ten meters of water adds almost exactly one more atmosphere.
- Speed grows with depth (v = √(2gd)) but the time to fall grows with height (t = √(2y/g)). Range = v·t = 2√(d·y), largest when depth = height: the middle hole, 2.0 m out. The top and bottom jets tie at 1.73 m.
- Range = 2√(d·y) with d + y = 2 m. Setting 2√((2 − y)·y) = 1.6 gives y = 0.4 m or y = 1.6 m: two holes, one low and fast, one high and slow, land in the same spot.
- On Mars the water leaves slower (v = √(2gd) is smaller) and falls slower (t = √(2y/g) is longer). Range = v·t = 2√(d·y): no g at all. Still 2.0 m.
- P = P₀ + ρgh = 101 325 + 1025 × 9.81 × 10 994 Pa ≈ 1.106 × 10⁸ Pa ≈ 1092 atm: about 1.1 metric tons pressing on every square centimeter. (This uses constant density and g; real measurements differ by a few percent.)
About the model
- Hydrostatics: absolute pressure P = P₀ + ρgh with P₀ = 101 325 Pa (1 atm) at the open surface; density and g are constant with depth (real seawater compresses slightly and g varies a little, so real deep-ocean pressures differ by a few percent).
- The tank is large, so the water level stays constant during the run. Holes are small and ideal (no jet contraction or friction losses): water leaves horizontally at Torricelli’s speed v = √(2g·d), d = depth below the surface.
- The first water leaving each hole is a projectile with no air resistance, so it lands at 2√(d·y) from the wall (y = hole height). Landing is solved exactly; the steady stream behind it follows the same parabola.
- Holes are plugged until the clock starts (t = 0). Three-hole mode puts holes at ¼, ½ and ¾ of the water depth.
- The dive gauge is separate from the tank: it reads P = P₀ + ρg·depth for the chosen depth (it appears once the run starts). The pressure–depth graph shows the same law.
- Jets are drawn thicker than real streams so they can be seen.
Every number on screen comes from the simulation, and each lab passes automated checks against the physics formulas. Spotted a mistake? Tell us.