What you’ll explore
How hot must the air be to lift you? In this lab you heat the air in a hot-air balloon until it lifts off and test your intuition against a real physics simulation.
Challenge levels
- How light is hot air?. Outside it is 15 °C (air 1.225 kg/m³). The pilot heats the air inside the envelope to 100 °C at the same pressure. How dense is that hot air, in kg/m³?
- How much can it lift?. The envelope holds 2,800 m³. With the air inside at 100 °C and 15 °C outside, how many kilograms can the hot air lift (envelope, basket and people included)?
- Lift off with 500 kg. Balloon, basket, burner, fuel and two people weigh 500 kg in total. Choose the air temperature the pilot holds so the balloon lifts off, without heating the fabric past 70 °C.
- What if: a hot day. Same 500 kg balloon, but it is 30 °C outside. At what inside temperature does it now lift off, in °C?
Key ideas
Show the explanations (spoilers: try the levels first)
- At fixed pressure, density goes as 1/T in kelvin: 1.225 × 288.15/373.15 ≈ 0.946 kg/m³. That is ρ = PM/(RT), the ideal gas law rearranged. The missing air is what makes the balloon light.
- Lift = (ρ_out − ρ_in)·V = (1.225 − 0.946) × 2800 ≈ 781 kg. Buoyancy is the weight of the displaced cool air minus the weight of the hot air inside.
- It floats when (ρ_out − ρ_in)·V = 500 kg: ρ_in = 1.225 − 500/2800 ≈ 1.046 kg/m³, which is air at about 337 K = 64 °C. Anything from 65 °C up lifts; hotter just climbs faster.
- Outside air at 30 °C is only 1.164 kg/m³, so the inside must reach 1.164 − 0.179 = 0.986 kg/m³: about 358 K = 85 °C. Pilots fly at dawn in summer for exactly this reason.
About the model
- Air is an ideal gas (dry air, M = 28.96 g/mol) at 1 atm; the envelope is open at the bottom, so the air inside is always at the outside pressure. Density ρ = PM/(RT): heating the air inside makes it expand and part of it spills out of the mouth.
- Lift (kg) = (ρ_out − ρ_in)·V: the weight of the cool air the envelope pushes aside, minus the hot air inside. The balloon leaves the ground when this reaches the total load (envelope, basket, burner, fuel and people, 400–900 kg in the videos).
- Heating: burner at full power (3 MW, typical of a two- to four-person balloon) until the air reaches the pilot’s set temperature, then throttled to just replace the heat lost through the fabric, modeled as h·(T − T_out) with h = 5 kW/K. Because the envelope is open, heating the air needs ρ(T)·V·c_p per kelvin, which gives an exact logistic curve for T(t). Real pilots burn in bursts; the smooth average is what the model shows.
- The air inside is taken as one uniform temperature (real envelopes are hotter at the top). The fabric limit is about 120 °C, so the set temperature is capped there.
- After lift-off the climb uses buoyancy minus weight minus drag (C_d = 0.5 on the envelope’s cross-section), with the moving mass = load + air inside; added mass and the thinning of the air with height (under 1 % over 50 m) are ignored.
- The balloon is drawn at true size (2,800 m³, about 17.5 m across) with a schematic basket and no people.
Every number on screen comes from the simulation, and each lab passes automated checks against the physics formulas. Spotted a mistake? Tell us.