What you’ll explore
What if you lift the load without moving the counterweight? In this lab you run a tower crane: counterweight, torque and a swinging load and test your intuition against a real physics simulation.
Challenge levels
- Place the counterweight. The crane lifts a 4 t load 30 m out. The jib steel (6 t) has its center 10 m out on the same side. How far behind the tower must the 12 t counterweight sit so the net torque is zero, in m?
- Pulling harder at lift-off. The hoist lifts the 4 t load with an upward acceleration of 0.5 m/s² until it reaches full speed. What is the cable tension while it speeds up, in kN?
- Heavy load, how far out?. Now a 10 t load, lifted at 0.5 m/s², with the counterweight still at 15 m. The base can resist 1,766 kN·m. Put the trolley as far out as you can, at least 26 m, without tipping the crane.
- What if the trolley stops dead. What if the trolley carries the load in from 30 m to 20 m at 1 m/s and stops dead? The load hangs on a 20 m cable and swings. How long is one full swing, in seconds?
- What if you don’t move the counterweight. What if the counterweight stays set for an empty jib (12 t at 5 m) and you slowly lift a 4 t load 30 m out? How much net torque must the base hold, in kN·m?
Key ideas
Show the explanations (spoilers: try the levels first)
- Torques about the tower must cancel: 12 t × c = 4 t × 30 m + 6 t × 10 m = 180 t·m, so c = 15 m.
- Newton’s 2nd law on the load: T − m·g = m·a, so T = 4000 × (9.81 + 0.5) ≈ 41.2 kN, about 5% more than its weight.
- While the load speeds up, its torque is 10 t × (g + a) × x. With the counterweight’s help the base can take up to x ≈ 28.5 m. Beyond that the crane tips.
- A pendulum of length L swings with period T ≈ 2π√(L/g) = 2π√(20/9.81) ≈ 8.97 s, whatever the load weighs. That’s why crane operators wait out a swing instead of fighting it.
- Net torque = g × (4 t × 30 m + 6 t × 10 m − 12 t × 5 m) ≈ 1,177 kN·m. It is under the base’s 1,766 kN·m limit, so it holds, but with far less margin. A heavier load would tip it.
About the model
- The crane is rigid and stands on a ballasted base (60 t, 3 m half-width). It tips when the net torque about the tower axis exceeds what the base can resist, 60 t × g × 3 m ≈ 1,766 kN·m (a simplified overturning check; real cranes use load charts and wind allowances).
- Net torque = cable pull × trolley distance + g × (6 t jib steel × 10 m − counterweight × its distance). The jib steel and counterweight are lumped masses; the tower’s own weight acts on the axis and adds no torque.
- The hoist accelerates at a up to 1 m/s, then climbs steadily and stops dead at the top (no slow-down phase), so cable pull is m(g + a) then m·g. The trolley moves at 1 m/s and the load rides along without swinging until the trolley stops dead.
- After the stop the load swings as a simple pendulum on its cable (point mass, no air drag, rigid cable). The cable’s extra pull during the swing and its sideways component are ignored in the torque, and the swing is integrated with RK4.
- When the crane tips, the run ends 1.5 s later; the tilt drawn is only indicative (toppling dynamics aren’t simulated). Loads and cranes are drawn roughly to scale; arrows are not to scale.
Every number on screen comes from the simulation, and each lab passes automated checks against the physics formulas. Spotted a mistake? Tell us.