What you’ll explore
Keep heating melting ice. Does its temperature rise? In this lab you heat ice at a steady power all the way to steam and test your intuition against a real physics simulation.
Challenge levels
- The thermometer while it melts. 1 kg of ice at −20 °C sits on a steady 1 kW heater. When half of the ice has melted, what does a thermometer in the ice–water mix read, in °C?
- How long to melt?. 1 kg of ice already at exactly 0 °C sits on a 1 kW heater (1,000 J every second). How long does it take to melt all of it, in seconds? (Latent heat of fusion of ice: 334 kJ/kg.)
- Melt it in two minutes. Back to 1 kg of ice at −20 °C. Choose the heater power so the last ice melts after 2 minutes (120 s ± 3 s).
- From 0 to 100. At 1 kW, the ice is now all melted: 1 kg of water at 0 °C. How many seconds until it starts to boil? (Water needs 4,186 J per kg per °C.)
- What if: all the way to steam. Now a 3 kW heater takes 1 kg of ice at −20 °C all the way until the last water has boiled away. How many times longer is the flat part at 100 °C (boiling) than the flat part at 0 °C (melting)?
Key ideas
Show the explanations (spoilers: try the levels first)
- While ice and water coexist the mix stays at the melting point, 0 °C. Every joule from the heater is spent breaking bonds in the crystal (latent heat), not on making molecules move faster, so the thermometer does not move until the last ice has melted.
- Melting needs m·L_f = 1 kg × 334,000 J/kg = 334 kJ. At 1,000 J per second that is 334 s, over five and a half minutes, with the temperature stuck at 0 °C the whole time.
- The heater must supply 2090 × 20 = 41.8 kJ to warm the ice and 334 kJ to melt it: 375.8 kJ in 120 s, so P ≈ 3.13 kW.
- Warming 1 kg by 100 °C needs 1 × 4186 × 100 = 418.6 kJ. At 1,000 J/s that is about 419 s: longer than melting, even though melting did not change the temperature at all.
- Boiling needs L_v = 2,257 kJ/kg, melting L_f = 334 kJ/kg. With the same heater the times are in the same ratio: 2257 / 334 ≈ 6.8 times longer.
About the model
- Heating curve at constant heater power P: every joule goes into the sample (no losses to the air or the pan). Heat added E = P·t, so each stage ends at t = E/P and the state is closed form in time.
- Constants: c_ice = 2090 J/(kg·K), c_water = 4186 J/(kg·K), latent heat of fusion L_f = 334 kJ/kg, latent heat of vaporisation L_v = 2257 kJ/kg (at 100 °C, 1 atm). Specific heats are taken as constant over each range.
- The sample is assumed well mixed: while ice and water coexist the whole mix sits at 0 °C, and while it boils at 100 °C. Real pans have hot spots and the thermometer lags a little; supercooling and superheating are ignored.
- Boiling at 1 atm (sea level). The run ends when the last water has boiled off; heating the steam itself is not modeled.
- The beaker drawing is schematic: the ice block, water column and steam puffs show the mass fractions, not exact shapes (ice is drawn resting in the water, a floating block would sit about 90 % under).
- Videos fast-forward at a different rate in each stage (keyframes on the stage boundaries) so every caption plays over its own stage; the graph always shows the real time axis.
Every number on screen comes from the simulation, and each lab passes automated checks against the physics formulas. Spotted a mistake? Tell us.