What you’ll explore
What if the shocks are worn out? In this lab you tune a car’s shock absorber over a bump and test your intuition against a real physics simulation.
Challenge levels
- Read the damping. A 400 kg quarter-car on a 20,000 N/m spring has a 1,697 N·s/m shock absorber. What is its damping ratio ζ = c ÷ (2√(k·m))? (The lab measures it from how fast the bounces shrink.)
- Who jumps highest?. Three cars hit the same 6 cm bump: worn shocks (ζ = 0.1), tuned (ζ = 0.7) and rock-hard (ζ = 3). Which car’s body rises highest? Type its ζ.
- Tune the shocks. Tune the shock absorber: after the bump the body must settle within 1 s, dip no more than 5% of the bump height below the road, and rise no more than 4 cm (comfort).
- Worn out. What if the shocks wear out and lose three quarters of their damping (c: 3,960 → 990 N·s/m)? How long (s) until the body settles within 5% of the bump height? (New shocks: 0.57 s.)
- No shocks at all. Remove the shock absorber entirely (c = 0). How many times per second (Hz) does the body bounce? m = 400 kg, k = 20,000 N/m.
Key ideas
Show the explanations (spoilers: try the levels first)
- ζ = c ÷ (2√(k·m)) = 1697 ÷ (2 × √(20,000 × 400)) = 1697 ÷ 5657 ≈ 0.30. Each bounce is about 1.5× smaller than the one before (the log decrement 2πζ/√(1−ζ²) ≈ 1.98).
- A damper resists fast motion in both directions. A rock-hard one almost locks the body to the wheel, so the body rises nearly the full 6 cm (≈ 5.3 cm). The worn one rises less (≈ 2.8 cm) but keeps bouncing for 3 s. Good shocks sit in between.
- Too little damping and the body keeps bouncing; too much and it passes the bump straight into the cabin. Car makers aim for ζ around 0.7–1 (here c ≈ 4,000–6,000 N·s/m).
- With a quarter of the damping (ζ ≈ 0.18) each bounce only shrinks a little, so it takes ≈ 1.7 s, three times longer, and the body dips 25% below the road on the rebound.
- f = √(k/m) ÷ 2π = √50 ÷ 2π ≈ 1.13 Hz. Car suspensions are tuned near 1–1.5 Hz because that feels like a calm walking pace; without a damper the bouncing would never stop.
About the model
- Quarter-car model: one corner of the car body (400 kg) on a linear spring (20,000 N/m) and a linear viscous damper (force ∝ relative speed). Real shock absorbers are stiffer in rebound than in compression; that asymmetry is ignored.
- The tire is treated as rigid (the wheel follows the road exactly) and the wheel has no mass of its own; a full model adds a tire spring and an unsprung mass with its own ~10 Hz wheel hop.
- Road input: a half-sine bump 6 cm high and 0.6 m long, driven over at 5 m/s (18 km/h), so the wheel is on it for 0.12 s. Gravity is balanced at rest, so heights are measured from the resting ride height.
- Motion is solved exactly in every regime (under-, critically and over-damped): a sinusoidal particular solution during the bump, then the free response. Vertical motion is drawn 5× exaggerated so centimeters are visible; the graph and HUD show real values.
- “Settled” = the last moment the body is more than 5% of the bump height (3 mm) from rest. Note: over a bump, harder damping settles faster but passes more of the bump to the body; “critical is fastest” holds for a body released from rest, not for road input.
- The car is already rolling when the clock starts (the builder guide’s moving-start exception); its body is at rest vertically until the bump.
Every number on screen comes from the simulation, and each lab passes automated checks against the physics formulas. Spotted a mistake? Tell us.