What you’ll explore
Dilute acid 10×: does pH go from 2 to 20? In this lab you dilute an acid step by step and watch the pH and test your intuition against a real physics simulation.
Challenge levels
- Read the stock. The first beaker holds 0.010 M hydrochloric acid, a strong acid: every HCl gives up its H⁺. What is its pH?
- Dilute it 10×. Take 10 mL of that acid and top it up to 100 mL with pure water: a 10× dilution. What is the new pH?
- Hit pH 5. Starting from the 0.010 M stock, choose how far to dilute it (as a power of ten) so the last beaker reads pH 5.00 ± 0.05.
- What if: a million times. Dilute the 0.010 M acid a million times (10⁶×). The "add 1 per 10×" rule says pH 8: a base! What does the last beaker really read?
- A weak acid. Now 0.10 M acetic acid (the acid in vinegar, Ka = 1.8 × 10⁻⁵). Only a small share of its molecules give up H⁺. What is its pH?
Key ideas
Show the explanations (spoilers: try the levels first)
- A strong acid is fully split, so [H⁺] = 0.010 mol/L = 10⁻² mol/L and pH = −log₁₀(10⁻²) = 2.00.
- 10× less acid means [H⁺] = 0.001 = 10⁻³ mol/L, so the pH goes up by exactly one step: 3.00.
- Each 10× dilution adds 1 to the pH of a strong acid, so going from pH 2 to pH 5 takes three of them: 10³ = 1000×, down to 10⁻⁵ M.
- Water itself splits into H⁺ and OH⁻ (Kw = 10⁻¹⁴). At 10⁻⁸ M of acid, [H⁺] = (C + √(C² + 4Kw)) / 2 = 1.05 × 10⁻⁷ M, so pH = 6.98: just below neutral, never above.
- Solve Ka = x² / (C − x): x = [H⁺] = 1.33 × 10⁻³ M, so pH = 2.88. Only 1.3% of the acetic acid molecules are split.
About the model
- pH = −log₁₀[H⁺] with [H⁺] in mol/L, using concentrations in place of activities (fine below about 0.1 M; at 1 M the real pH of HCl is slightly lower).
- Water’s own ions are included (Kw = 1.0 × 10⁻¹⁴ at 25 °C). For a strong acid the charge balance gives [H⁺] = (C + √(C² + 4Kw)) / 2, so a very dilute acid approaches pH 7 from below and can never turn basic.
- Acetic acid uses Ka = 1.8 × 10⁻⁵ (pKa 4.74, 25 °C). Its pH solves the full charge balance [H⁺] = Ka·C/(Ka + [H⁺]) + Kw/[H⁺] numerically; at 0.1 M this matches the textbook quadratic (Kw neglected) to 0.01%.
- Serial dilution: every beaker is topped up to 100 mL. A full step pipettes 10 mL into 90 mL of water (10×); a final partial step uses a larger aliquot so the total dilution is exactly 10ⁿ. Pipetting errors and CO₂ from the air (which makes real “pure” water about pH 5.6) are ignored.
- Beaker colors approximate a universal indicator (red → orange → yellow → green at 7 → blue → violet); real indicator shades vary by brand.
Every number on screen comes from the simulation, and each lab passes automated checks against the physics formulas. Spotted a mistake? Tell us.